Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
   + Mechanical part of engine G16
   + Mechanical part of engine J20
   - Engine cooling
      + The general description
      + Diagnostics
      + Maintenance service
      - Vehicle routine maintenance
         Plums of a cooling liquid
         Hoses or water pipes of system of cooling
         The thermostat
         Belt of the cooling fan
         The cooling fan and муфта the fan
         Radiator
         The water pump
         The gauge of temperature of a cooling liquid of the engine (EATS)
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

The water pump

Removal

For engine G16

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) from the accumulator.
  2. Merge cooling system.
  3. Remove a gear belt of a drive and натяжитель, having addressed to Section a drive Belt газораспределительного the mechanism and the tension device for a belt in the Head Engines.
  1. Remove rubber consolidation (1) between the oil pump and the water pump.
  1. Remove directing oil щупа (1) with oil щупом.
  1. Remove the adjusting lever of the generator (1).
  1. Remove knot of the water pump (1).

Do not assort the water pump. If it is required to repair the pump, replace it as the uniform unit.

For engine J20

 PERFORMANCE ORDER

  1. Disconnect a negative cable (-) from the accumulator.
  2. Merge cooling liquid.
  3. Disconnect a final hose of a radiator from a cover of the thermostat (2).
  4. Remove a bolt of an exhaust pipe of a heater (1).
  5. Remove a generator belt, having turned off a pulley натяжителя. Address to Section a generator Belt in the Head electric equipment System.
1 — a bolt of an exhaust pipe of a heater
2 — a final hose of a radiator
3 — a cover of a final collector
  1. Remove knot of the water pump (1), having removed it 4 bolts (2).

Do not turn off an adjusting pin when remove the water pump (1).


1 — knot of the water pump
2 — 4 bolts
3 — a thermostat cover

Check

For engine G16

Повращайте the water pump a hand to check up, how much exactly it functions. If the pump rotates not smoothly or makes noise, replace it.

For engine J20

Do not assort the water pump. If it is necessary to repair the pump, replace it as the uniform unit.


 PERFORMANCE ORDER

  1. Повращайте the water pump a hand to check up, how much exactly it functions. If the pump rotates not smoothly or makes noise, replace it.
  2. Check up, whether the driving wheel (2) water pumps (1) is damaged. If it is necessary, replace.

Do not assort the water pump to check up the driving wheel of the water pump.


1 — the water pump
2 — the driving wheel
3 — кольцеобразное consolidation

Installation

For engine G16

 PERFORMANCE ORDER

  1. Put a new lining for the pump (2) in the block of cylinders.
  1. Establish the water pump (1) in the block of cylinders. The rotating moment of an inhaling: a bolt of the water pump (engine G16) () — 12 Н•м (1.2 kg th, 8.5 pound on foot).
  1. After installation of the water pump put rubber consolidation (1) between the water pump and the oil pump.
  1. Establish натяжитель a belt, a gear belt of a drive and an external cover of a gear belt of a drive, having addressed to Section a drive Belt газораспределительного the mechanism and the tension device for a belt in the Head Engines.
  1. Establish the adjusting lever of the generator (1).
  1. Establish directing oil щупа (1), having greased with engine oil кольцеобразное consolidation (2).
  1. Establish a pulley коленвала, a pulley of the water pump, a belt of a drive of the pump, the cooling fan / муфту and a fan casing.
    • The rotating moment of an inhaling
      • Nuts of the cooling fan/mufty (engine G 6): 11 Н•м (1.1 kg th, 8.0 pound on foot)
      • Bolts of a pulley №2 коленвала (engine G16): 16 Н•м (1.6 kg th, 11.5 pound on foot)
  2. Adjust a tension of a belt of the cooling fan as earlier it has been described.
  3. Connect a negative cable (-) to the accumulator.
  4. Fill in cooling liquid.
  5. After installation check up each detail on a leaking.

For engine J20

 PERFORMANCE ORDER

  1. Put new кольцеобразное consolidation (1) on the water pump (2).

Do not forget to put adjusting pins on the party of the water pump before to place the water pump in the engine block.

  1. Establish the water pump (1), using new bolts (2) on the block of cylinders and fasten them to the specified rotating moment. The rotating moment of an inhaling: a bolt of the water pump (engine J20) () — 27 Н•м (2.7 kg th, 19.5 pound on foot).

Use new bolts (only 4) to establish the water pump in the engine block. If it not to make, water can leak.


1 — the water pump
2 — bolts
3 — a thermostat cover
  1. Establish a bolt of an exhaust pipe of a heater (1).
  2. Establish a generator belt. Address to the Head electric equipment System.
  3. Establish a final hose of a radiator on a cover of the thermostat (2).
  4. Fill in cooling liquid.
  5. Connect a negative cable to the accumulator.
1 — a bolt of an exhaust pipe of a heater
2 — a final hose of a radiator
3 — a cover of a collector of an exhaust system