Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
- Electric equipment
   + Body electric equipment
   + Illumination system
   - Electric equipment system
      + The general description
      + Diagnostics
      + The works made on the car
      - Major repairs
         - The generator
            Removal
            Installation
            Dismantling [Type 60 A]
            Dismantling [Type 70 A and 80 A]
            Survey [Type 60 A]
            Survey [Type 70 A and 80 A]
            Replacement of brushes
            Assemblage [Type 60 A]
            Assemblage [Type 70 A and 80 A]
      + Specifications
      The inhaling moments
   + Tools/information for drivers







e8f2b5b1

Survey [Type 70 A and 80 A]

Rotor

 PERFORMANCE ORDER

  1. Using an ohmmeter, check up electroconductivity between contact rings of a rotor. If there is no electroconductivity, replace a rotor. Standard resistance: nearby 2.9.

  1. Using an ohmmeter, check up, whether there is no electroconductivity between contact rings and a rotor. If there is an electroconductivity, replace a rotor.
  1. Check up contact rings, whether there is no roughness or a deposit. If they rough or are a deposit, replace a rotor.
  1. Using a calliper with нониусом, measure diameter of a contact ring.
    • Standard diameter: 14.2-14.4 mm (0.557 - 0.567 inches)
    • The minimum diameter: 12.8 mm (0.504 inches)
  1. If diameter less minimum, replace a rotor.

Статор

 PERFORMANCE ORDER

  1. Using an ohmmeter, check up electroconductivity of all contacts. If there is no electroconductivity, replace статор.
  1. Using an ohmmeter, check up, whether there is no electroconductivity between contacts статора and the core статора. If there is an electroconductivity, replace статор.

Brush and щеткодержатель

Check up each brush on deterioration, having measured its length, as shown. If the brush is worn out to a limit, replace a brush. Address to Section Replacement of brushes in this Chapter.
  • Length of an open part of a brush "a":
    • The standard: 10.5 mm (0.413 inches)
    • Limit: 4.5 mm (0.351 inches)

The rectifier

The positive rectifier

 PERFORMANCE ORDER

  1. Using an ohmmeter, connect one щуп a tester to plug "B", and another – to each of rectifier plugs.
  2. Replace polarity щупов a tester and repeat item 1.
  3. Check up that one shows conductivity presence, and another – is not present.
  4. If there is an electroconductivity, replace the rectifier.
1 — plug "B"
2 — the rectifier plug

The negative rectifier

 PERFORMANCE ORDER

  1. Using an ohmmeter, connect one щуп a tester to each of negative contacts, and another to each of rectifier plugs.
  2. Replace polarity щупов a tester and repeat item 1.
  3. Check up that one shows conductivity presence, and another – is not present.
  4. If there is an electroconductivity, replace the rectifier.
1 — negative contact
2 — the rectifier plug

The bearing

 PERFORMANCE ORDER

  1. Check up that the drive and the bearing has no jags and are not worn out.
  1. Check up that the casing of the bearing has no jags and is not worn out.