Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
- Suspension bracket
   - Forward suspension bracket
      The general description
      + Diagnostics
      - Service out of a workshop
         The stabilizer of cross-section stability/plug
         Shock-absorber rack
         Cylindrical spring
         The terminator of a dynamic course of a suspension bracket / a rubber nest of a spring
         Wheel nave (including the wheel bearing)
         Sharnir/os rotations
         The suspension bracket/plug lever
   + Back suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

Sharnir/os rotations

Removal

 PERFORMANCE ORDER

  1. Remove a wheel nave. See in the given Chapter Has undressed a wheel Nave (including the wheel bearing).
  2. Remove a lock ring of a shaft of a forward drive (1) and a persistent washer of a forward axis of a fist (2) (at the all-wheel drive car) or a cap of a nave of a forward wheel (at the car with a drive on two wheels).
1 — a ring of a shaft of a forward drive
2 — a persistent washer of a forward axis of a fist
3 — a drive shaft
4 — a wheel spindle
  1. Disconnect the end of steering draught (1) from a fist (2).
  1. Remove the stabilizer of cross-section stability. See in the given Chapter Has undressed the Stabilizer of cross-section stability/plug.
  2. Remove a nut of a hairpin with a spherical tip.
  3. Prop up the bottom lever a jack.
  4. Remove bolts with скобы racks.
1 — a rack
2 — a fist
  1. By means of a stripper disconnect a fist from a hairpin with a spherical tip.
  1. Lowering a jack, remove kulak/os a wheel fist.
  2. Remove an internal oil epiploon (at the all-wheel drive car), a cap of a fist (4) (at the car with a drive on two wheels), a cover from a dust (1) and an axis of a fist of a wheel (2).
1 — a cover from a dust
2 — an axis of a fist of a wheel
3 — a fist
4 — a fist cap

For the all-wheel drive car

  1. Remove the bearing of a shaft of a drive (2) by means of the special tool.
    • The special tool
      • (A): 09923-74510
      • (B): 09930-30102
1 — a wheel spindle

Installation

 PERFORMANCE ORDER

  1. For installation of a fist, an oil epiploon of an axis of a fist of a wheel and the bearing of a shaft of a drive (2) execute in return sequence of manipulation on removal, paying attention to the following.

The all-wheel drive car

1 — an axis of a fist of a wheel
3 — a persistent washer of a shaft of a forward drive (type “C” or “D”)
4 — an internal oil epiploon
6 — an oil epiploon of a shaft of a drive
With — flat type
D — фланцевый type (for a cabriolet)

The car with a drive on two wheels

1 — an axis of a fist of a wheel
5 — a fist cap

For the all-wheel drive car

  1. By means of the special tool establish the bearing of a shaft of a drive (1).
    • The special tool:
      • (A): 09913-76010 — a persistent washer of a shaft of a drive of type With
      • (A): 09913-80112 — a persistent washer of a shaft of a drive of type D
      • Persistent washer of a shaft of a drive of type And
      • The size “a”: 0 – 1 mm (0 – 0.04 inches)
      • Persistent washer of a shaft of a drive of type In
      • The size “a”: 1.75 – 2.50 mm (0.069 – 0.098 inches)
2 — a wheel spindle
  1. At installation of an axis of a fist of a wheel on a fist, process adjoining surfaces hermetic. “A”: hermetic 99000-31110.

For the all-wheel drive car

  1. Besides, fill a flute in an axis of a fist of a wheel approximately with ten grammes plastic литиевой greasings. “B”: greasing 99000-25010.
  1. Tighten a nut of an axis of a fist of a wheel to the specified value of the moment of an inhaling. The inhaling moment: a nut of an axis of a fist of a wheel (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).

For the all-wheel drive car

  1. Pressing establish an internal oil epiploon.
  1. By means of the special tool enter inside an internal oil epiploon while its end will not concern a step surface of a fist.
    • The special tool:
      • (B): 09944-66010
      • (C): 09924-74510

For the all-wheel drive car

  1. Put plastic литиевую greasing on an edge of an oil epiploon and in its cavity, having filled it more, than on 60 %.
  2. Put литиевую plastic greasing “A” on a shaft of a drive (2). “A”: greasing 99000-25010.
  3. Pressing establish a persistent washer of a shaft of a forward drive (3) on a shaft of a drive (2) if it has been removed (for a persistent nut of a shaft of a drive of type). Put литиевую plastic greasing “A” on a persistent washer of a shaft of a drive. “A”: greasing 99000-25010.
  4. Put литиевую plastic greasing “A” and establish a persistent washer of a shaft of a forward drive (3) rounded off by the party to the central party (for a persistent washer of a shaft of a drive of type). “A”: greasing 99000-25010.
Type With — a flat washer
Type D — развальцованная a washer

For the car with a drive on two wheels

  1. Remove greasing, old hermetic and a dirt from adjoining surfaces of a cap of a fist (2) and a fist (1), on a pure surface of a cap in regular intervals put water-proof hermetic and establish a cap on a fist. “B”: hermetic 99000-31090.
1 — a fist
2 — a fist cap
3 — a wheel spindle
  1. Tighten a nut of the lever of a hairpin with a spherical tip. For this purpose take a new nut and tighten it to the specified value of the moment of an inhaling. The inhaling moment: a nut of a hairpin with a spherical tip (a): 60 Н•м (6.0 kg th, 43.5 pounds-foots).

For the car with a drive on two wheels

  1. Put water-proof hermetic on an adjoining surface of a nave of a wheel (1) and establish a cap of a nave (2) on a wheel nave. “A”: hermetic 99000-31090.

For the all-wheel drive car

  1. At installation of a flange of a drive of the bridge (1) on a wheel nave, put hermetic on an adjoining surface of a flange of a drive of the bridge (1). “A”: hermetic 99000-31090. The inhaling moment: a bolt of a flange of a drive (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).
  1. For installation of a nave of a wheel see in the given Chapter Has undressed a wheel Nave (including the wheel bearing).
  1. Connect a tip of steering draught to a fist and tighten a new nut of a tip of steering draught. The inhaling moment: a nut of a tip of steering draught (a): 40 Н•м (4.0 kg th, 29.0 pounds-foots).