Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
+ Mechanical part of engine G16
- Mechanical part of engine J20
+ The general description
+ Routine maintenance
- Assembly armature of the engine
Major repairs
Bearings коленвала, коленвал and the block of cylinders
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Bearings коленвала, коленвал and the block of cylinders
Components
|
|
*2) Put hermetic 99000-31250 on the interfaced surface of the pallet картера, having addressed to point 5 of procedure of installation. |
|
|
*6) Grease with engine oil internal surfaces of the bearing. |
|
|
*7) Establish the party of the bearing with flutes faced to cheeks коленвала. |
|
|
*17) Put hermetic 99000-31110 on the carving party. |
|
|
The rotating moment of an inhaling. |
|
|
To grease with engine oil. |
Removal
|
|
- Remove knot of the engine from a vehicle, having addressed to Section the Engine in this Chapter.
- Remove coupling and a flywheel (for vehicles М/Т) or a leading disk (for vehicles А/Т). To remove coupling address to Section a coupling Cover, a disk of coupling and a flywheel In the Head Coupling. The special tool (): 09924-17811.
- Remove the case throttle заслонок, an inlet collector, an exhaust system collector.
- Remove маслосборник and a grid of the oil pump, having addressed to Razdelu Maslosbornik and a grid of the oil pump in this Chapter to remove.
- Remove the oil pump.
- Uncover cylinder heads.
- Uncover synchronisation chains, having addressed to Section the Cover of a chain of synchronisation in this Chapter for the purpose of dismantle.
- Remove directing to a synchronisation chain, натяжитель chains, regulators натяжителя, the second chain of synchronisation and the first chain of synchronisation.
- Remove knot of a head of the cylinder.
- Remove pistons and rods.
- Remove the position gauge коленвала (1).
|
|
1 — the position gauge коленвала
2 — the cylinder block
3 — коленвал |
|
|
- Remove the water pump (1) and a heater exhaust pipe.
|
- Remove arms of lateral fastening of the engine (2) (right and left).
- Ослабьте bolts картера also remove them.
|
|
1 — the pallet картера
2 — a bolt (diameter of a carving of 10 mm)
3 — a bolt (diameter of a carving of 8 mm) |
- Remove коленвал from the block of cylinders.
|
|
Check
Коленвал
Deterioration коленвала
|
|
With the help циферблатного the indicator measure deterioration on a neck in the centre. Slowly rotate коленвал. If deterioration exceeds limit rates, replace коленвал. A deterioration limit коленвала: 0.06 mm (0.0023 inches). |
Backlash of the persistent bearing коленвала
|
|
|
|
- Measure this backlash when коленвал is regularly in the block of cylinders, i.e. when the persistent bearing and the pallet картера (1) on the place. Twirl bolts картера, having addressed to item 6 of procedure of installation.
|
- Use циферблатный a measuring instrument to take readings of a deviation in an axial direction коленвала. If the deviation falls outside the limits norms, replace the persistent bearing on new the standard size or большего the size to receive a standard backlash.
- Backlash of the persistent bearing коленвала
- Norm: 0.10 – 0.35 mm (0.0040 – 0.0137 inches)
- Limit: 0.42 mm (0.0165 inches)
Thickness of the persistent bearing коленвала
|
The size of the bearing
|
Thickness
|
|
The standard
|
2.500 mm (0.984 inches)
|
|
The bolshego size (0.125 mm (0.0049 inches))
|
2.563 mm (0.1009 inches)
|
|
|
1 — the persistent bearing
2 — a lubricant flute |
|
|
Эллипсность and a bias (non-uniform deterioration) necks коленвала
|
|
The difference speaks about non-uniform deterioration of a neck коленвала in diameter of cross-section section or along its length (or both that, and another). This difference if that is, is defined under indications a micromeasure. If one of necks is strongly damaged or if the general non-uniform deterioration how it has been explained above, falls outside the limits norm, переточите or replace коленвала.
- Limit эллипсности and a neck bias коленвала: 0.01 mm (0.0004 inches)
- эллипсность: And – In
- Bias: and – b
|
Radical bearings
The general information
Radical bearings коленвала for repair are presented in the standard size and in the size less standard on 0.25 mm (0.0098 inches), and each of them is presented by 5 types of the bearings different from each other by the admission.
|
|
The top half of bearing (1) has a lubricant flute (2). Establish this half with a lubricant flute in the block of cylinders. |
On the bottom half of bearing the lubricant flute is absent.
Check
Check up bearings on a subject изъязвления, scratches, deterioration or damage. If any defects are found out, replace both the top and bottom halves. Never replace one half, without having replaced other half.
Backlash of the radical bearing коленвала
|
|
- Check up a backlash by means of a plaster solution, having executed the following procedure.
- Remove the pallet картера.
- Clean bearings and necks коленвала.
|
|
- Put a part of a plaster solution (1) for full width of the bearing (in parallel коленвалу) on a neck, bypassing oil apertures.
|
- Establish the pallet картера (1) on the block of cylinders. Fasten bolts картера, observing последовательност. Fasten bolts картера with the specified rotating moment.
- The rotating moment of an inhaling:
- Bolt картера from 10-mm a carving in diameter (0.394 inches) (): 60 Н•м (6.0 kg th, 43.5 pound on foot)
- Bolt картера from 8-mm a carving in diameter (0.315 inches) (b): 27 Н•м (2.7 kg th, 19.5 pound on foot)
|
|
Do not turn коленвал with a plaster solution inside. |
|
|
1 — the pallet картера
2 — a bolt (diameter of a carving of 10 mm)
3 — a bolt (diameter of a carving of 8 mm) |
|
|
- Remove the pallet картера and by means of a ruler (2) measure width on a plaster covering (1) in the widest point. If the backlash falls outside the limits norm, replace the bearing. Always replace the top and bottom half, as a unit. The new standard bearing can create a necessary backlash. If it has not occurred, it is necessary переточить a neck коленвала that it was possible to use the bearing of the smaller size of 0.25 mm (0.00984 inches). Having chosen the new bearing, check up a backlash repeatedly.
|
- Bearing backlash коленвала
- Norm: 0.032 – 0.052 mm (0.0013 – 0.0020 inches)
- Limit: 0.060 mm (0.0023 inches)
|
|
Choice of radical bearings коленвала
The standard bearing
|
|
- If the bearing in failure condition or if the backlash of the bearing falls outside the limits norm, choose the new standard bearing according to the following procedure, and establish it.
- At replacement коленвала or the block of cylinders and the pallet картера for any reason choose new standard bearings to establish them according to numbers printed on new коленвале, and-or the letters printed on the new pallet картера.
|
|
|
- At first check up diameter of a neck. As is shown in drawing, on cheeks коленвала №2 (3) figures are printed. Three types of figures («1», «2» and «3») represent the next diameters of necks.
Technical characteristics of necks коленвала
|
The printed figures
|
Diameter of necks
|
|
1
|
58.000 – 58.0060 mm (2.2835 – 2.2836 inches)
|
|
2
|
57.9940 – 57.9999 mm (2.2833 – 2.2834 inches)
|
|
3
|
57.9880 – 57.9939 mm (2.2830 – 2.2832 inches)
|
- The figures printed on a cheek №2 коленвала, designate diameters of necks noted стрелочкой in drawing, accordingly. For example, the printed figure "1" specifies that diameter of a corresponding neck makes 58.000 – 58.0060 mm (2.2835 – 2.2836 inches).
|
|
1 — the pulley party коленвала
2 — the flywheel party
3 — a cheek коленвала |
- Further check up internal diameter картера (a bearing cover) without the bearing. On the pallet картера it is printed five letters. Three letters ("And", "In" and "With") designate the next internal diameters of covers.
Technical characteristics of internal diameters of covers of bearings коленвала
|
The printed letters
|
Internal diameter of covers of bearings (without bearings)
|
|
AND
|
62.0000 – 62.0060 mm (2.4409 – 2.4411 inches)
|
|
IN
|
62.0061 – 62.0120 mm (2.4412 – 2.4414 inches)
|
|
WITH
|
62.0121 – 62.0180 mm (2.4415 – 2.4416 inches)
|
- The letters printed on the pallet картера, specify for internal diameter картера, noted by an arrow in drawing, accordingly. For example, the letter "And", printed on a cover of the bearing №2, specifies that internal diameter of a cover of the bearing №2 makes 62.0000 – 62.0060 mm (2.4409 – 2.4411 inches).
|
|
1 — a cover of the bearing №1
2 — a cover of the bearing №2
3 — a cover of the bearing №3
4 — a cover of the bearing №4
5 — a cover of the bearing №5
6 — the pulley party коленвала
7 — the flywheel party |
- There are five types of the standard bearings different from each other on a thickness. That they could be distinguished, they are painted in following colours in a place shown in drawing. Each colour designates a certain thickness in the bearing centre.
Technical characteristics of bearings коленвала
|
Colour
|
Thickness of the bearing
|
|
The green
|
1.990 – 1.994 mm (0.07835 – 0.07850 inches)
|
|
The black
|
1.993 – 1.997 mm (0.07847 – 0.07862 inches)
|
|
Colourless (there is no paint)
|
2.996 – 2.000 mm (0.07859 – 0.07874 inches)
|
|
The yellow
|
1.999 – 2.003 mm (0.07870 – 0.07885 inches)
|
|
The blue
|
2.002 – 2.006 mm (0.07882 – 0.07897 inches)
|
- On the figure printed on a cheek коленвала №2 and letters, printed on the pallet картера, define the new standard bearing which should be established on a neck, having addressed to the table resulted more low. For example, if the figure printed on a cheek коленвала №2 «1», and the letter printed on the pallet картера, – "In", establish the new standard bearing painted in "Black" colour on its neck.
Technical characteristics of the new bearing коленвала the standard size
|
|
The figure printed on a cheek коленвала
(Diameter of a neck)
|
|
1
|
2
|
3
|
|
The letter printed on the pallet картера (internal diameter of a cover of the bearing)
|
AND
|
The green
|
The black
|
The colourless
|
|
IN
|
The black
|
The colourless
|
The yellow
|
|
WITH
|
The colourless
|
The yellow
|
The blue
|
|
|
|
To establish the new bearing of the standard size
|
- Check up a bearing backlash at the new chosen bearing of the standard size, having addressed to subsection Radical bearings коленвала in this Section. If the backlash still falls outside the limits norm, use the following bearing on a thickness of the size and recheck a backlash.
|
|
The bearing of the smaller size (0.25 mm (0.009842 inches))
The bearing of the smaller size on 0.25 mm (0.009842 inches) is presented by five types different from each other on a thickness. That they could be distinguished, each bearing is painted in following colours in a place specified in drawing. Each colour represents a certain thickness in the bearing centre.
Thickness of bearings of the smaller size коленвала
|
Colour
|
Thickness of the bearing
|
|
Green and red
|
2.115 – 2.119 mm (0.08327 – 0.08342 inches)
|
|
Black and red
|
2.118 – 2.122 mm (0.08339 – 0.08354 inches)
|
|
Only the red
|
2.121 – 2.125 mm (0.08351 – 0.08366 inches)
|
|
Yellow and red
|
2.124 – 2.128 mm (0.08363 – 0.08377 inches)
|
|
Blue and red
|
2.127 – 2.131 mm (0.08374 – 0.08413 inches)
|
If it is necessary, переточите a neck коленвала and choose for it the bearing of the smaller size as follows.
|
|
- Переточите a neck till next complete diameter. Complete diameter of a neck коленвала: 57.7439 – 57.7560 mm (2.2734 – 2.2738 inches).
|
|
- With the help a micromeasure measure переточенный diameter of a neck. Measurement indications should act in film in two directions perpendicularly each other to check up эллипсность.
|
- By means of diameter of a neck measured above, and the letters printed on the pallet картера, choose the bearing of the smaller size, having addressed to the table resulted more low. Check up a backlash of the bearing with the new chosen bearing of the smaller size.
Bearing technical characteristics коленвала the smaller size
|
|
The measured diameter of a neck
|
|
57.7500 – 57.7560 mm (2.2737 – 2.2738 inches)
|
57.7440 – 57.7499 mm (2.2734 – 2.2736 inches)
|
57.7380 – 57.7439 mm (2.2732 – 2.2733 inches)
|
|
The letters printed on the pallet картера
|
AND
|
Green and red
|
Black and red
|
Only the red
|
|
IN
|
Black and red
|
Only the red
|
Yellow and red
|
|
WITH
|
Only the red
|
Yellow and red
|
Blue and red
|
|
|
Bearings of the smaller size to installation
|
|
|
Asterisk of the oil pump
|
|
Check up a teeth of an asterisk (2) about deterioration or damage. If any damage or deterioration is revealed, replace коленвал (1). |
Chain of a drive of the oil pump
|
|
Check up a chain of a drive of the oil pump about deterioration or damage. |
Back oil consolidation
|
|
Attentively check up back oil consolidation about deterioration or damage. If its edge is worn out or damaged, replace it. |
Flywheel
|
|
- If the gear wreath is damaged, will burst or is worn out, replace a flywheel.
- If the surface contacting to a disk of coupling, is damaged or worn strongly out, replace a flywheel.
|
|
- Check up a flywheel about deterioration of an obverse surface with the help циферблатного the indicator. If deterioration exceeds admissible norms, replace a flywheel. A limit of deterioration of a flywheel: 0.2 mm (0.0078 inches).
|
|
|
The block of cylinders
Deformation of the condensed surface
|
|
With the help калибромера check up the condensed surface about deformation and if планшетность exceeds admissible norms, correct it. A limit of deformation of the block of cylinders: 0.06 mm (0.0024 inches). |
Хонингование or расточка cylinders
|
|
- If it is required to chisel one of the cylinders, all other cylinders should be chiseled also in one and too time. Pick up the piston большего the size according to the general deterioration of the cylinder.
Diameter of the piston
|
The size
|
Diameter of the piston
|
|
The standard
|
83.970 – 83.990 mm (3.3059 – 3.3066 inches)
|
|
The size is more on 0.50 mm (0.02 inches)
|
84.470 – 84.480 mm (3.3256 – 3.3263 inches)
|
- With the help a micromeasure measure diameter of the piston.
- Calculate, what internal diameter of the cylinder is necessary for chiseling, as follows:
- D = AND + IN – WITH
- D: Internal diameter of the cylinder which is necessary for turning.
- And: the Measured diameter of the piston.
- In: a piston Backlash = 0.02 – 0.04 mm (0.0008 – 0.0015 inches)
- With: the Admission for хонингования = 0.02 mm (0.0008 inches)
|
|
1 — 26.5 mm (1.04 inches) |
- Chisel and хонингуйте the cylinder to settlement parametres.
|
|
Before to chisel, establish the pallet картера and fasten according to technical requirements to avoid deformation of internal diameters of bearings. |
- Measure a backlash of the piston after хонингования.
|
|
The lock valve
|
|
Check up the lock valve on presence засора and formations of the got stuck lumps. |
Installation
|
|
- All parts of installation should be washed ideally up.
- Do not forget to grease a neck коленвала, basic bearings, persistent bearings, шатунные a neck, rod bearings, pistons, piston rings and trunks of cylinders.
- Basic bearings, картер (covers of bearings), rods, bearings of rods, covers of bearings of rods, pistons and piston rings are united in separate sets. Do not separate such sets and provide at installation that each detail has returned there, whence it has come.
- Clean the interfaced surface of the block of cylinders and the pallet картера, remove oil, old hermetic and a dust from the interfaced surface.
|
|
|
- Establish radical bearings коленвала (4) in the block of cylinders (1). One of two halves of the bearing коленвала has an oil flute (3). Establish this half with an oil flute in the block of cylinders, and other half without an oil flute in the pallet картера. Be convinced that both halves are noted by the same paint.
- Establish ring consolidation (2) in the block of cylinders.
|
|
1 — the block of cylinders
2 — ring consolidation
3 — an oil flute
4 — bearings коленвала
5 — a pin |
|
|
- Establish persistent bearings (1) in the block of cylinders between №2 and №3 cylinders. The parties with an oil flute (2) turn an obverse surface to cheeks коленвала.
|
|
|
- Place коленвал (1) with a chain of a drive of the oil pump in the block of cylinders. Be convinced that on a plate of the gauge of position коленвала (2) there are no metal particles and damage.
|
- Put hermetic "And" on the interfaced surface of the pallet картера (1). "And": hermetic 99000-31250.
|
|
"And" — 3 mm (0.12 inches)
«b» — 2 mm (0.08 inches)
1 — a pallet surface картера
2 — the bearing |
- Establish the pallet картера (1) in the cylinder block. Having greased with engine oil all bolts картера ((1) – (22)), fasten them gradually, as follows.
|
|
- Tighten bolts (1) – (10) to 42 Н•м (4.2 kg th, 30.5 pound on foot) according to digital order.
|
- Ослабьте bolts (1) – (10) until the rotating moment of an inhaling will not decrease to 0 (zero) as it should be the return to fastening.
- Just as in point 7, fasten them to 42 Н•м (4.2 kg th, 30.5 pound on foot).
- In the same way, as in point 7, fasten them with the specified rotating moment.
- Fasten bolts (11) – (22) with the specified rotating moment according to their digital order.
- The rotating moment of an inhaling:
- Bolt картера with a carving of 10 mm in diameter (1) – (10)
- (): 60 Н•м (6.0 kg th, 43.5 pound o
| | |
