Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
- Suspension bracket
- Forward suspension bracket
The general description
+ Diagnostics
- Service out of a workshop
The stabilizer of cross-section stability/plug
Shock-absorber rack
Cylindrical spring
The terminator of a dynamic course of a suspension bracket / a rubber nest of a spring
Wheel nave (including the wheel bearing)
Sharnir/os rotations
The suspension bracket/plug lever
+ Back suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
The suspension bracket/plug lever
Removal
|
|
- Remove a cylindrical spring. The Section the Cylindrical spring see in the given Chapter.
- Remove bolts and nuts of the lever of a suspension bracket. Then remove the suspension bracket lever.
- Cautiously, not to damage a face surface of the lever of a suspension bracket, cut off фланцевую a part of the plug of the lever of a suspension bracket (rubber and a steel). The size “A”: about 6 mm (0.236 inches).
|
|
1 — a cut off flange
2 — external diameter of the plug |
|
|
- Put the lever of a suspension bracket and the special tool on a hydraulic press. Combine a cut off flange of the lever of a suspension bracket with the welded part (1) special tools, and the party of connection with the lever of a suspension bracket with a step part (2) special tools. The special tool (A) — 09951-46020.
|
|
|
With extra care pull out the plug of the lever of a suspension bracket to press it vertically. Otherwise it is possible to be traumatised. |
|
|
- Remove the forward plug, having pulled out it by means of a hydraulic press (1) and the special tool.
- The special tool:
- (A): 09951-46020.
- (B): 09924-74510
- (C): 09951-16060
|
|
|
- Remove the back plug, having pulled out it by means of a hydraulic press (1) and the special tool.
- The special tool:
- (A): 09951-46020
- (D): 09913-80112
- (E): 09925-58210
|
|
|
Installation
The forward plug
By means of the special tool, press the forward plug (2) while its flange will not concern edges of the case of the lever of a suspension bracket.
- The special tool
- (C): 09951-16060
- (F): 09913-85210
|
|
Plug cave-in can be facilitated if to process an internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
And — the plug flange concerns case edges |
The back plug
|
|
- By means of the special tool, press the back plug (2) while its flange will not concern edges of the case of the lever of a suspension bracket.
- The special tool
- (E): 09925-58210
- (F): 09913-85210
|
|
Plug cave-in can be facilitated if to process an internal surface of the case of the lever of a suspension bracket soap water or oil with additives. |
|
|
1 — a hydraulic press
2 — the back plug
And — the plug flange concerns case edges |
- Establish the suspension bracket lever on the chassis.
- Lower the car in position without loading and tighten a nut of the lever of a suspension bracket to the specified value of the moment of an inhaling.
|
|
|
|
In model with engine H27 do not use repeatedly back nut of the forward lever of a suspension bracket (1). |
|
- The inhaling moment:
- Forward nut of the lever of a suspension bracket (a): 85 Н•м (8.5 kg th, 61.5 pounds-foots)
- Back nut of the lever of a suspension bracket (b): 126 Н•м (12.6 kg th, 91.0 pound-foot)
- Further installation is similar to installation of a cylindrical spring. The Section the Cylindrical spring see in the given Chapter.
|
|
|
|
