Suzuki Grand Vitara SQ416/SQ420/420WD

1. Remove a drum of a back brake. See Has undressed the Brake drum (Removal) in the Head the Lay and back brake more in detail.

2. Merge oil from the bridge case, having weakened a drain stopper.

3. Remove nuts (1) stoppers of the bearing of a back wheel from the bridge case.

4. Remove the gauge of speed of a wheel (1) from the case of the back bridge (if there is a system of antiblocking of brakes ABS).

• At removal of the gauge of speed of a back wheel do not pull and excessively do not overwind a wire.
• Do not damage a surface of the gauge of speed of a back wheel or a rack and try, that the dust and a dirt have not got to its adjusting aperture.

5. Check up that there is a backlash between a stopper of the bearing of a back wheel (1) and the lever колодки a lay brake (2). If the backlash (3) is not present, ослабьте a cable counternut so that there was a backlash.

6. By means of the special tool (B) and (C) pull out the bridge.
• The special tool:
• (C): 09943-35512
• (B): 09942-15510

Operate cautiously that together with bridge not to pull out a brake plate.

Pull out the bridge cautiously not to hook on the top both bottom brake racks and a lay cable.

7. The pulled out shaft of the back bridge.
   • Length of a shaft “L”:
     • Left-hand side: 711.5 mm (28.0 inches)
     • The right party: 757.5 mm (29.8 inches)

8. If there is a system of antiblocking of brakes ABS to remove a rotor of the gauge from a lock ring, grind the grinding tool one part of a rotor of the gauge until it does not become thin.

9. Break a chisel истонченную a part of a rotor of the gauge to remove it (if there is a system of antiblocking of brakes ABS).

10. To remove a lock ring (1) from a shaft (3), grind the grinding tool two parts (2) lock rings of the bearing (1) until they do not become thin.

Be not overzealous with polishing not to damage a shaft.

11. Break a chisel истонченную a part of a lock ring to remove it.

12. Remove the bearing (2) from a shaft (1) by means of a hydraulic press (3).

14. By means of a hydraulic press (2) remove a hairpin (hairpins) (1).

The quantity of the greasing put in a cavity of an oil epiploon, should occupy more than 60 % of its empty seat. “A”: greasing 99000-25010.

4. Establish a stopper of the bearing (2) on a shaft (1).

• Operate cautiously not to damage an outer side of a lock ring.
• Establish the wheel bearing in a correct direction.

6. For the car with system of antiblocking of brakes ABS, establish by means of a press a new rotor of the gauge (1).

Operate cautiously not to damage an outer side of a lock ring.

8. Put hermetic on an adjoining surface of a stopper of the bearing (1) with a brake plate.

Before drawing of new hermetic clear a surface of the old. “B”: hermetic 99000-31110.

9. Establish a shaft of the back bridge in the case of the bridge and tighten nuts of a stopper of the bearing to the specified value of the moment of an inhaling. The inhaling moment: a stopper nut (a): 23 Н•м (2.3 kg th, 17.0 pounds-foots).

At installation of the back bridge operate cautiously not to damage edge of an oil epiploon in the bridge case.

10. Tighten a bolt of the gauge of speed of a wheel to the specified value of the moment of an inhaling (if there is a system of antiblocking of brakes ABS). The inhaling moment: a bolt of the gauge of speed (b) — 21 Н•м (2.1 kg th, 15.5 pounds-foots).