Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
- Fuel system
- Current maintenance service of a vehicle
The fuel pump
The fuel filter
Fuel wires
Cover of a jellied fuel mouth
Fuel tank
Technical characteristics of the rotating moment of an inhaling
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Fuel tank
Removal
|
|
- Dump pressure of fuel in striking топливопроводе.
|
|
This work cannot be made, if the engine hot. If it to make, it can negatively affect the catalyst. |
- Disconnect a negative cable (-) from the accumulator.
|
|
- Insert a fuel hose (1) manual pumps into a hose of a jellied mouth of a fuel tank and merge fuel in an interval "And" in drawing (to merge fuel through an interval until fuel will not cease to flow).
|
|
|
Do not insert a hose of the manual pump into a fuel tank. It you can damage the inlet (lock) valve (2). |
- Remove a protector of a hose of a jellied mouth of a fuel tank.
|
|
- Disconnect a hose of a jellied mouth (3) from a fuel tank (1) and a hose сапуна (2) from a neck of a jellied mouth.
|
- Remove the inlet valve of a fuel tank (4). Be cautious, do not damage the inlet valve at съеме.
- Drain a fuel tank, having pumped out the pump fuel through a bulk mouth of a fuel tank. Use the manual pump to drain a fuel tank.
|
|
Never merge or do not store fuel in the open container because of possible ignition or explosion. |
- Disconnect an inlet hose of a bulk mouth (3) from a bulk mouth of a fuel tank (1).
|
|
1 — a mouth of a fuel tank
2 — a final hose of a bulk mouth of a fuel tank
3 — an inlet hose |
|
|
- Disconnect a steam fuel hose (1) and a return fuel hose (2) from pipes.
|
- Remove a protector of a fuel tank from a vehicle.
|
|
- Slowly lower a fuel tank, keeping it in horizontal position, and remove everyone муфту from the fuel pump (1) and the pressure gauge in a fuel tank (2).
|
|
|
Check
Having removed a fuel tank, check up hoses and the pipes connected to a fuel tank, on presence of leak, easing of connection, deterioration or damage. And also check up, whether leaks the fuel pump and level gauge linings. Visually examine a fuel tank on presence of leakings and damage. Replace any damaged or faulty details.
Installation
|
|
-
Establish knot of the fuel pump (2) and the valve отсечки fuel (15) on a fuel tank (1). Address to Section the Fuel pump in this Chapter.
- Connect fuel hoses to a fuel tank (1), the valve отсечки fuel (15) and knot of the fuel pump (2). After connection reliably fix clips of hoses.
- Insert the inlet valve (14) into a fuel tank (1). If it was deformed or damaged otherwise, replace it with the new.
- Establish a fuel tank (1) by means of belts (10) fuel tanks, and then establish a protector (9) on a vehicle.
- The rotating moment of an inhaling:
- Bolt of a fuel tank (): 50 Н•м (5.0 kg th, 36.5 pound on foot)
- Bolt of a protector of a fuel tank (): 50 Н•м (5.0 kg th, 36.5 pound on foot)
- Connect a hose of a jellied mouth (13) to a fuel tank (1) and a hose сапуна (5) to a neck of a jellied mouth (11). Reliably fix their clips.
- The rotating moment of an inhaling
- Hose clip сапуна (b): 2.0 Н•м (0.2 kg th, 2.0 pound on foot)
- Clip of a hose of a jellied mouth (): 4.0 Н•м (0.4 kg th, 3.0 pound on foot)
- Establish a protector of a hose of a jellied mouth of a fuel tank.
|
|
- Connect fuel парошланг (1) and a return fuel hose (2) to a fuel pipe and reliably fix their clips.
|
- Connect an inlet hose of the fuel filter (3) to the fuel filter (1).
|
|
1 — the fuel filter
2 — a final hose of the fuel filter
3 — an inlet hose |
- Connect муфту to knot of the fuel pump and the pressure gauge in a tank, accordingly.
- Connect a negative cable (-) to the accumulator.
- On termination of installation check up, whether the fuel system leaks.
|
|
Procedure of a purge of a fuel tank
|
|
This procedure of a purge will not remove all fuel steams. Do not try to make the repair of a tank demanding application of fire or a flame as there can be an explosion conducting to a personal traumatism. |
The following procedure is used for a purge of a fuel tank.
|
|
- Having removed a fuel tank, disconnect all hoses and knot of the fuel pump from a fuel tank.
- Merge all rests of fuel from a tank.
- Carry a tank in a washing zone.
- Fill a tank with warm water or water from under the crane, well shake up and merge. Repeat this procedure обмыва until in a tank it is not becomes pure. Replace a tank, if it inside the rusty.
- Completely pour out the rests of water after washing up.
|
|
|
|
