Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
- Forward and back differentials
- Forward диффренциал
+ The general description
+ Diagnostics
- Service out of a workshop
+ Servicing
+ Check
- Removal and installation
Differential accessories
Removal
Installation
+ Back differential
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Removal and installation
Differential accessories
|
|
- Lift the car and turn a steering wheel to the right.
- Separate fixing arm R from the differential case, having removed bolts from its bottom part.
- Remove fixing arm R, having removed a forward fixing bolt from its top part.
|
|
1 — a fixing bolt of an arm
2 — fixing arm R
3 — the differential case |
|
|
2 — fixing arm R
3 — the differential case
4 — a forward fixing bolt |
- Remove fixing arm L, having removed the top and bottom fixing bolts.
|
|
1 — the differential case
2 — a forward fixing bolt
3 — fixing arm L
4 — a bolt of a fixing arm |
- Check up a condition of each plug. If it is damaged or spoilt, pull out its special tool and a hydraulic press and replace.
- The special tool
- (a): 09951-26010
- (b): 09951-16080
- At installation on a press arrange шлицу in each plug.
|
|
1 — fixing arm L
2 — the plug
3 — fixing arm R
And — alignment шлицы 45 ° |
- Arrange each plug on an arm. Length “a”: 3.0 mm (0.12 inches).
|
|
1 — fixing arm R
2 — fixing arm L |
|
|
- At installation observe following values of the moment of an inhaling:
- The inhaling moment
- (a): 85 Н•м (8.5 kg th, 61.5 pounds-foots)
- (b): 50 Н•м (5.0 kg th, 36.5 pounds-foots)
|
|
|
Back fixture (for the holder of forward differential)
Integral type
|
|
- Lift the car and remove a fixing design, having removed two bolts and nuts from outside the holder of differential and 2 bolts and nuts from outside cross-beams.
- Check up fixing rubber on damages and deterioration of a condition and replace if necessary.
- At installation observe following value of the moment of an inhaling. The inhaling moment (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).
|
|
1 — a bolt and a nut of a back fixing arm
2 — the holder of differential
3 — a cross-beam
4 — a bolt of a back fixing arm
5 — back fixture of differential |
|
|
Type with the plug
|
|
- Lift the car and remove a back fixing arm, having removed a back fixing bolt and bolts of a back fixing arm.
- Check up fixing rubber on damages and deterioration of a condition and replace if necessary.
- At installation tighten back fixing bolts and bolts of a back fixing arm to the specified value of the moment of an inhaling.
- The inhaling moment:
- Back fixing bolt (a): 85 Н•м (8.5 kg th, 61.5 pounds-foots)
- Bolts of a back fixing arm (b): 50 Н•м (5.0 kg th, 36.5 pounds-foots)
|
|
1 — a back fixing bolt
2 — a bolt of a back fixing arm
3 — a back fixing arm |
|
|
|
|
