Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
- Steering
   + Suspension bracket, wheels and tyres
   + Adjustment of corners of installation of wheels of a forward suspension bracket
   + System of the hydraulic booster of a wheel
   - Steering wheel and steering column
      - Steering wheel and steering column the safety not equipped with a pillow
         The general description
         + Diagnostics
         - Service out of a workshop
            Steering wheel
            Podrulevye switches
            Steering column (at not a cabriolet)
            The top shaft of a steering (at not a cabriolet)
            Steering column (at a cabriolet)
            The steering lock (the ignition switch)
            The bottom shaft of a steering
            Check of a steering column on presence of damages at failure (at a cabriolet)
            Check of a steering column and the top shaft of a steering on presence of damages at failure (at not "cabriolet")
            The lever of an adjustable unblocking of a steering column
         Specifications of the moment of an inhaling
         The special tool
      + Steering wheel and steering column with a safety pillow
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

Steering column (at not a cabriolet)  

When the steering column is removed from the car, it is very easy for damaging.

If it to drop vertically, the steering shaft can break or can ослабнуть plastic pins which regulate length of a column; if against it to lean, it can be bent or deformed. Any of the listed damages can worsen ударопоглощающие properties of a column.

Weakening fixing bolts and nuts of a steering column, be convinced that the steering column and the top steering shaft are separated. If before easing of fixing bolts and nuts a steering column and the top steering shaft not to separate, it can damage top муфту and fixing скобу the top steering shaft.


At carrying out of service of a steering column or any knots established on it it is necessary to remove a steering wheel. But if the steering column acts in film to provide only access to components of the panel of tools, the steering wheel can to be removed from a column.

Removal

 PERFORMANCE ORDER

  1. Disconnect "minus" (–) a battery cable.
  2. Remove a steering wheel and подрулевые switches if it is required. Sections the Steering wheel and Podrulevye switches See in the given Chapter.
  3. If a steering wheel and \or подрулевые switches remain on a place, execute following manipulations:
    • Turn a steering wheel so that forward wheels of the car looked directly forward.
    • Turn the ignition switch in position “LOCK” and pull out a key.
Uncover a steering column (1).
  1. Disconnect all cables of following knots:
    • Contact spiral and подрулевых switches
    • The ignition switch
    • Elements of anticreeping system (if are available).
  1. Remove a bolt (1) and a nut (2) top муфты the top steering shaft.
  1. Remove a steering column (1), fixing bolts (2 pieces) (2) and nuts (2 pieces) (3).
  1. If there is a cable of blocking of the switch (key) (1), disconnect it from the ignition switch, having turned the ignition switch in position “ACC”.
  1. Remove a steering column from the car.

Survey

Check up serviceability of a steering column and presence of damages as it is described in the given section in the head «Check of a steering column and the top shaft of a steering on presence of damages at failure».

Installation

After a tightening of fixing bolts of a steering column it is necessary to tighten bolts муфты a steering shaft.


 PERFORMANCE ORDER

  1. Be convinced that position of forward wheels and a steering wheel correspond to rectilinear movement of the car.
  1. If there is a cable of blocking of the switch (key) (1), connect it to the ignition switch, having turned the ignition switch in position “ACC”. Then turn the ignition switch in position “LOCK”.
  1. Combine a point “A” a steering column (1) with a nut aperture “B” top муфты the top steering shaft. Then connect top муфту the top steering shaft.
  1. Establish a steering column (1) contact top party bottom шлиц to fixing bolts. Tighten the bottom fixing nuts (3) steering columns, and then the top fixing bolts (2) to the specified values of the moment of an inhaling. The inhaling moment: fixing bolts and nuts of a steering column — 25 Н•м (2.5 kg th, 18.0 pounds-foots).
  1. Establish a bolt (2) top муфты the top steering shaft and a nut (1). Tighten a nut (1) top муфты the top steering shaft till the specified moment of an inhaling. The inhaling moment: a nut top муфты the top steering shaft (a) — 23 Н•м (2.3 kg th, 17.0 pounds-foots).
  1. If have been removed подрулевые switches, establish them as it is described in the given Chapter in Razdele Podrulevye switches.
  2. Connect all cables which were disconnected at removal of a steering column.
  1. Establish a cover of an aperture of a steering column (1).
  1. If the steering wheel has been removed, establish it as the Steering wheel is described in the given Chapter in Section.
  2. Connect "minus" (–) a cable to the battery.