Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
- The general information
   - Safety measures
      - Safety measures at work with the cars equipped with pillows of safety
         Diagnostics
         Service and leaving
   The basic safety measures
   Safety measures at work with the catalyst
   Safety measures at service of electric chains
   + Procedure of check of electric chains
   Interrupting or weak connection
   Safety measures at installation of means of a mobile communication
   + The identification information
   Warning, warning and information labels
   Places of lifting of the car
   The list of the reductions used in the given management
   + The metric information
   The standard moments of inhalings
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

Service and leaving

Many service procedures demand switching-off of a safety lock of a pillow of safety and switching-off from a food of all modules of pillows of safety in order to avoid emergency operation.

Driver's and passenger modules of pillows of safety

For leaving and storage of not worked module «air bag» it is necessary to choose a place with an ambient temperature more low 65°С (150°F), with low degree of humidity and far from electric hindrances.

At transportation of not worked module, take the side of its opening from itself. In case of emergency operation, the pillow will work with the minimum possibility of damage. Never bear the module of a pillow of safety for wires or for коннектор on a module underside. At placing of not worked module on a workbench or other surface always put its pillow upwards from a surface. Since not worked module of a pillow of safety should be the facing panel upwards, put it on a workbench with a cut or use a vice for reliable fixing for its bottom fixing скобу. It is necessary to provide free space for pillow operation since in case of emergency operation. Non-observance of this condition can lead to traumas.

Never throw out worked modules «air bag» (driver's and passenger). If it is necessary, necessarily blow up them before emission.

The module of a pillow of safety right after operations becomes very hot. Wait at least a floor of hour to cool it for performance of the further actions.

After the module of a pillow of safety has worked, its surface can contain порошкообразные the combustion rests. This powder mainly consists of corn starch (used for pillow greasing at надувании) and by-products of chemical reaction. For many service procedures it is necessary to use gloves and goggles.

A. The module of a pillow of safety should not be close to a body during opening.

B. The module of a pillow of safety should be strongly fixed at the stand.

1 — a cut in the stand
2 — the tightening adaptation
3 — the bottom assembly arm

КДМ

During service operations be very cautious at service of the kontrolno-diagnostic module (КДМ). Never shake and do not strike on КДМ.

Never submit a food to system «air bag» while КДМ it is not connected rigidly to the car. All details of fastening КДМ and an adjusting arm should be tightened according to the established moment and the arrow should specify in a forward part of the car to provide correct functioning of system «air bag».

КДМ it can be activated at food giving if it is not connected rigidly to the car that can lead to traumas.

Driver's and passenger преднатяжители seat belts

For leaving and storage not worked преднатяжителя a seat belt choose a place with an ambient temperature more low 65°С (150°F), with low degree of humidity and far from electric hindrances.

Never bear преднатяжитель a belt for a wire or коннектор. At placing not worked преднатяжителя a belt on a workbench or other surface never put its aperture for tap of gases from top to bottom. Also it is forbidden to put something on a surface with a final aperture or to put преднатяжители belts against each other. Non-observance of this condition can lead to traumas.

Never throw out worked преднатяжители seat belts (driver's and passenger). If it is necessary, necessarily activate them before emission.

Преднатяжитель a seat belt right after operations becomes very hot. Wait at least a floor of hour to cool it for performance of the further actions.

For many service procedures it is necessary to use gloves and goggles to prevent possible irritation of a skin and an eye.

1 — a final aperture

Even at the insignificant failure which have not caused operation of pillows of safety, necessarily check up components of system and the connected components.

At service of the components which are not concerning system «air bag» but if blow could damage system components replace these components beforehand.

At care of modules of pillows of safety (driver's and passenger), преднатяжителями seat belts (driver's and passenger) or КДМ, be attentive, do not drop and do not strike them. If there was a strong blow (for example, falling from height in 91.4 sm (3 foots) or it is more), do not try to disassemble or repair, simply replace new.

When greasing, a washing-up liquid, oil, water have etc. got to the module «air bag» (driver's and passenger) or in преднатяжитель a seat belt (driver's and passenger), immediately wipe a dry rag.

System conducting «air bag» can be easily defined on yellow colour of a winding of wires and on yellow коннекторам. Be very attentive at work with them.

At detection of breakage, damage to conducting, коннекторе or contact replace a plait of wires, коннекторы and contacts in gathering.

Do not submit a food to system «air bag» while all components are not connected or the table of diagnostic process demands it since it will provoke an error code.

Never use system components «air bag» from other car.

At welding use, it is necessary to disconnect temporarily system «air bag».

Never subject system components «air bag» to direct influence of hot air (drying of the car after painting) or to open fire.

Labels WARNING/CAUTION are pasted on all components of system «air bag». Attentively follow instructions.

After repair is finished, execute diagnostic check of system «air bag».