Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
- Mechanical part of engine G16
+ The general description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Klapannyj backlash
Filtering element of the air filter
Cover of a head of cylinders
The case throttle заслонок and an inlet collector
Collector of the fulfilled gases
Drive belt газораспределительного the mechanism and the tension device for a belt
Маслосборник and a grid of the oil pump
The oil pump
Коромысло the valve, an axis коромысел and a cam-shaft
Valves and head of the block of cylinders
+ Piston rod, piston rings, rods and cylinders
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Mechanical part of engine J20
+ Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Drive belt газораспределительного the mechanism and the tension device for a belt
Components
|
|
The rotating moment of an inhaling. |
Removal
|
|
- Disconnect a negative cable from the accumulator.
- Drain antifreeze of the engine and disconnect an inlet hose from a radiator.
- Remove a belt of the pump of the strengthened steering (4) or compressor A/S belt if that is available.
- Remove the radiator fan, a pulley of the water pump, приводной a belt of the water pump and a fan casing.
|
|
1 — a pulley коленвала
2 — a pulley of the pump of the hydraulic booster of a steering
3 — А/С the compressor (if that is available)
4 — a belt of the pump of the strengthened steering |
|
|
- Remove a pulley коленвала, having turned away 5 bolts of a pulley (1).
|
|
|
- Remove an external cover of a belt of a drive газораспределительного the mechanism.
|
- To establish a drive belt газораспределительного the mechanism, level 4 marks of a tension, turning коленвал.
|
|
1 — a V-shaped mark in a cover of a head of the cylinder
2 — the tension is noted «Е» on a pulley of a belt of a drive газораспределительного the mechanism коленвала
3 — an arrow on a casing of the oil pump
4 — a stamped mark in a pulley of a belt of a drive газораспределительного the mechanism коленвала |
- Remove the tension device of a belt of a drive газораспределительного the mechanism, a plate of the tension device (2), a spring of the tension device (5) and a drive belt газораспределительного the mechanism (1).
|
|
1 — a drive belt газораспределительного the mechanism
2 — a plate of the tension device
3 — a bolt of the tension mechanism
4 — a hairpin натяжителя
5 — a spring of the tension device |
|
|
- After removal of a belt of a drive газораспределительного the mechanism never turn a cam-shaft and коленвал it is independent from each other more than on the distance shown in drawing. If to turn, there can be a wrong gearing between pistons and valves, and the parts concerning pistons and valves can be damaged.
- Never bend a drive belt газораспределительного the mechanism.
|
|
|
1 — a range of admissible turn for a cam-shaft-------- on a tension mark, within 90 ° from a mark «V» on a head cover in right and a left-hand side
2 — a range of admissible turn for коленвала-------- on a stamped mark, within 90 ° from an arrow on a casing of the oil pump to the left and to the right |
|
|
Check
|
|
|
|
- Check up a drive belt газораспределительного the mechanism on presence of deterioration or cracks. If necessary replace.
|
|
|
- Check up the tension device about smooth rotation.
|
|
|
Installation
|
|
|
|
- Establish a plate of the tension mechanism on the tension mechanism. Insert a ledge (1) plates of the tension mechanism into an aperture (2) in the tension mechanism.
|
|
|
- Establish the tension mechanism (2) and a plate of the tension mechanism (3):
- Do not tighten while a bolt of the tension mechanism (1) wrench. While fasten only manually.
- Be convinced that plate movement in a direction specified стрелочкой, forces the tension mechanism to move in the same direction.
- If between a plate and the tension mechanism there is no interconnected movement, remove the tension mechanism and a plate again and repeatedly insert a plate ledge into an aperture of the tension mechanism.
|
|
|
- Be convinced of that the adjusting label «Е» (2) on a pulley of a belt of a drive газораспределительного the cam-shaft mechanism is levelled with a mark "V (1) on a cover of a head of the cylinder. If it not so, combine two marks, having turned a cam-shaft, but be cautious, do not turn it more than on an admissible range of turn.
|
|
|
- Be convinced of that the stamped mark (2) on a pulley of a belt of a drive газораспределительного the mechanism коленвала is levelled with стрелочкой (1) on a casing of the oil pump. If it not so, level two marks, having turned коленвал, but be cautious, do not turn it more than on an admissible range of turn.
|
- Establish a drive belt газораспределительного the mechanism and (2). Having levelled two numbers of marks and having pushed a plate of the tension mechanism, establish a drive belt газораспределительного the mechanism on two pulleys so that приводная the party of a belt (1) was without any proweight. And then establish a spring of the tension mechanism, and manually fix a hairpin натяжителя (3).
|
|
The piston 4 is in this position above a zero point of a working course. |
|
|
1 — приводная the belt party
2 — a spring of the tension mechanism
3 — a hairpin натяжителя
4 — the shock-absorber |
|
|
- To eliminate sagging of a belt of a drive газораспределительного the mechanism, turn коленвал on two complete revolutions clockwise after its installation. Having convinced that sagging of a belt is not present, at first fix a hairpin натяжителя, and then a bolt of the tension mechanism by each specified rotating moment. Then be again convinced that two numbers of marks are levelled by appropriate amount.
- The rotating moment of an inhaling:
- Hairpin натяжителя: () — 11 Н•м (1.1 kg th, 8.0 pound on foot)
- Bolt of the tension mechanism: (b) — 27 Н•м (2.7 kg th, 19.5 pound on foot)
|
|
|
- Establish an external cover of a belt of a drive газораспределительного the mechanism. Before to establish, be convinced that consolidation is between the water pump and a casing of the oil pump. The rotating moment of an inhaling: a bolt of an external cover of a belt of a drive газораспределительного the mechanism () — 11 Н•м (1.1 kg th, 8.0 pound on foot).
|
- Establish a pulley коленвала (2).
|
|
- Level a pin (1) with an aperture of a pulley of a belt of a drive газораспределительного the mechanism коленвала, and twirl bolts of a pulley (3) by the specified rotating moment. The rotating moment of an inhaling: a pulley bolt коленвала () — 16 Н•м (1.6 kg th, 11.5 pound on foot).
|
- Establish a casing of the fan of a radiator, the pulley of the water pump cooling the fan and приводной a belt of the water pump. Adjust a tension приводного a belt of the water pump, having addressed to Section Regulation and check of a tension of a belt of the cooling fan in the Head engine Cooling.
- Establish a belt of the pump of the strengthened steering or compressor A/S belt if that is available. Adjust a belt tension, having addressed to Section the Engine in the Head Maintenance service and greasing.
- Connect an inlet hose of a radiator to a radiator.
- Back fill cooling system, having addressed to Section Washing and filling of system of cooling in the Head engine Cooling.
- Connect a negative cable to the accumulator.
- Check up, whether leaks antifreeze in a hose junction.
|
|
|
|
