Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
- Brake system
   - Brakes
      The general description
      + Diagnostics
      The diagnostic table
      - Check and adjustment
         Стравливание air from brakes
         Check of free height of the brake lever
         Adjustment of the light switch of brakes
         Check it is superfluous a pedal course
         Check of a free wheeling of the brake lever
         Check of level of a brake liquid
         Check of a brake hose and highway
         Check of the main cylinder
         Check of a brake disk
         Check brake колодки
         Check of a brake boot
         Check and adjustment of a lay brake
         Washing of hydraulic system of brakes
         Check of pressure of a liquid (if the car is equipped LSPV)
         Check of work of the brake amplifier
      Specifications - an inhaling twisting moment
      Necessary materials for service
      The special tool
   + Brake highway/hose the brake cylinder
   + Forward brakes
   + Lay and back brake
   + Antiblocking brake system (ABS)
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

Check and adjustment

Стравливание air from brakes

The brake liquid is very dangerous to a paint. If the liquid has casually got on the painted surface, immediately erase a brake liquid and clear the painted surface.


If the vehicle is equipped АБС, be convinced that the ignition switch is disconnected.

Necessarily pit air from brake system as set forth below when the oil hydrodrive is disconnected Hydraulic highways of brake system consist of two separate contours, one for brakes of forward wheels, another for brakes of back wheels. Стравливание air it is necessary for a brake of the right and left forward wheel, a brake of the left back wheel and LSPV (if the car has no АБС), i.e. in 4 places (3 places for vehicles with АБС).

Without АБС

1 — 4-foreign connection / 2-foreign connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — activator ABS
• — a point стравливания air
F — the forward party

WITH АБС

1 — 4-foreign connection / 2-foreign connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — activator ABS
• — a point стравливания air
F — the forward party

 PERFORMANCE ORDER

  1. Fill a tank of the main cylinder with a brake liquid and support its filled in at least half during time стравливания air.
  1. Remove спускную a stopper of a safety valve (1).
  1. Attach a vinyl tube (2) to спускной to a stopper of a safety valve of the brake cylinder, and insert other end into a vessel (3).
  1. Press some times on the brake lever, and then, keeping the lever in the pressed condition, release спускную a safety valve stopper approximately on one third-half of turn.
  1. When pressure of a liquid in the cylinder is lowered to a minimum, tighten a trigger stopper of a safety valve.
  1. Repeat operation until in a hydraulic line there will be no air vials.
  1. When vials will disappear, press and keep the brake lever and tighten a trigger stopper of a safety valve.
  • Inhaling twisting moment
    • Forward brake
    • Back brake
      • Trigger stopper of a safety valve of the wheel cylinder (a): 7.5 Н•м (0.75 kg th, 5.5 pounds on foot)
      • Trigger stopper of safety valve LSPV (if the car is equipped by it): 7.5 Н•м (0.75 kg th, 5.5 pounds on foot)
  1. Then attach a trigger stopper of a safety valve.
  1. After стравливания air, submit pressure of a liquid to the pipeline and check up, whether there is no leak.
  1. Fill up liquid level in a tank to the specified level.
  2. Check up the brake lever on "softness". If the lever "soft", repeat procedure стравливания air.