Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation


Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
- Electric equipment
   + Body electric equipment
   + Illumination system
   - Electric equipment system
      + The general description
      + Diagnostics
      + The works made on the car
      - Major repairs
         - The generator
            Removal
            Installation
            Dismantling [Type 60 A]
            Dismantling [Type 70 A and 80 A]
            Survey [Type 60 A]
            Survey [Type 70 A and 80 A]
            Replacement of brushes
            Assemblage [Type 60 A]
            Assemblage [Type 70 A and 80 A]
      + Specifications
      The inhaling moments
   + Tools/information for drivers






e8f2b5b1

Dismantling [Type 70 A and 80 A]

Type 70A

1 — a pulley nut
2 — a pulley
3 — a drive frame
4 — статор
5 — a carving hairpin
6 — the drive bearing
7 — the holder of the bearing
8 — a rotor
9 — edge of a casing of the bearing

10 — a bearing cover
11 — a back frame
12 — the rectifier
13 — an insulator
14 — a regulator
15 — a brush
16 — щеткодержатель
17 — a back cover

Type 85 A

1 — a pulley nut
2 — a pulley
3 — a drive frame
4 — статор
5 — a carving hairpin
6 — the drive bearing
7 — the holder of the bearing
8 — a rotor
9 — edge of a casing of the bearing
10 — a bearing cover
11 — a wavy washer

12 — a back frame
13 — a sealing cover
14 — the rectifier
15 — an insulator
16 — a regulator
17 — a brush
18 — щеткодержатель
19 — a cover щеткодержателя
20 — a back cover
21 — клеммный a guard


 PERFORMANCE ORDER

  1. Remove an internal nut of plug "B" and an insulator.
  2. Remove a back cover.
1 — a back cover
2 — an insulator
3 — an internal nut of plug "B"
  1. Remove 2 screws and extend assemblage щеткодержателя.
  2. Remove 3 screws and an IC-regulator.
  3. Uncover щеткодержателя with щеткодержателя.
1 — IC-regulator screws
2 — an IC-regulator
3 — screws щеткодержателя
4 — assemblage щеткодержателя
  1. Remove 4 screws, 1 bolt and the rectifier.
1 — the rectifier
  1. Remove 4 rubber insulators (only type 80 A).
1 — a rubber insulator
  1. Keeping a shaft шестигранным a wrench, remove a pulley nut, and then extend a pulley.
  • For shaft keeping use шестигранный a pulley. The dvenadtsatigrannyj key can slide off and damage a shaft or the tool.
  • Do not try to keep a pulley flat-nose pliers or a trumpet key not to damage it.

1 — a pulley
2 — шестигранный a key
3 — a cranked wrench
  1. Remove 4 nuts of a back frame.
  2. Beat out a back frame with a rotor, easily tapping on it with a plastic hammer.
  3. Cautiously separate a back frame from a rotor, using a plastic hammer.

Do not strike on a shaft from outside a contact ring when divide a rotor and a back frame.


1 — a back frame
2 — a rotor shaft
3 — a nut of a back frame
  1. If necessary use a stripper for bearings to remove a casing of the bearing and a bearing cover.
  2. Be cautious not to damage the blade of the cooling fan at stripper use.
1 — a bearing casing
2 — a bearing stripper
3 — a bearing cover
  1. If necessary remove 4 screws, a plate of the holder and then beat out the trailer bearing.
1 — a carving hairpin
2 — a keeping plate
3 — the final bearing
4 — статор
  1. If necessary, remove carving hairpins and extend статор.

Will remove статор easier if to warm up a frame.