Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
- Electric equipment
+ Body electric equipment
+ Illumination system
- Electric equipment system
+ The general description
+ Diagnostics
+ The works made on the car
- Major repairs
- The generator
Removal
Installation
Dismantling [Type 60 A]
Dismantling [Type 70 A and 80 A]
Survey [Type 60 A]
Survey [Type 70 A and 80 A]
Replacement of brushes
Assemblage [Type 60 A]
Assemblage [Type 70 A and 80 A]
+ Specifications
The inhaling moments
+ Tools/information for drivers
|
Assemblage [Type 70 A and 80 A]
|
|
- If casing bearing it is removed, establish it.
- Check up that it rotates smoothly.
|
|
1 — the casing bearing
2 — a rotor
3 — a bearing cover |
- If статор it is removed, establish статор and tighten carving hairpins.
- If the drive bearing is removed, establish it.
- Check up that it rotates smoothly.
- Inhaling twisting moment
- (a): 8.8 Н•м (0.88 kg th, 6.5 pounds-foots)
- (b): 2.6 Н•м (0.26 kg th, 2.0 pounds-foots)
|
|
1 — a carving hairpin
2 — a keeping plate
3 — the drive bearing
4 — статор |
- Place a drive frame on a pulley, and establish a rotor on a frame.
- Establish a back frame on приводную a frame.
- Tighten 4 nuts with the specified rotating moment. An inhaling twisting moment (a): 4.5 Н•м (0.45 kg th, 3.5 pounds-foots).
|
|
1 — a back frame
2 — приводная a frame |
- Establish a pulley and tighten a pulley nut, keeping a shaft шестигранным a wrench with the specified moment of an inhaling. An inhaling twisting moment (a): 111 Н•м (11.1 kg th, 80.5 pounds-foots).
|
|
1 — a pulley
2 — шестигранный a key
3 — a cranked wrench |
- Establish 4 rubber insulators.
- Establish the rectifier.
- Inhaling twisting moment
- (a): 2.0 Н•м (0.2 kg th, 1.5 pounds-foots)
- (b): 3.9 Н•м (0.39 kg th, 3.0 pounds-foots)
|
|
At rectifier installation, check up and be convinced that between contacts статор and blades of the cooling fan there is a sufficient backlash. |
|
|
- Establish a cover щеткодержателя on щеткодержатель.
|
- Place IC a regulator together with щеткодержателем horizontally on a back frame.
- Establish 5 screws while the backlash between щеткодержателем and a connector will not be about 1 mm (0.04 inches). An inhaling Twisting moment (a): 2.0 Н•м (0.2 kg th, 1.5 pounds-foots).
|
|
1 — an IC-regulator
2 — щеткодержатель
3 — a back frame |
- Establish a back cover and клеммную a plate.
- Inhaling twisting moment
- (a): 4.5 Н•м (0.45 kg th, 3.5 pounds-foots)
- (b): 3.8 Н•м (0.38 kg th, 3.0 pounds-foots) (only type 80 A)
- Establish an insulator and tighten an internal nut of plug "B" with the specified moment. An inhaling twisting moment (c): 4.2 Н•м (0.42 kg th, 3.0 pounds-foots).
|
|
1 — a back cover
2 — an insulator
3 — an internal nut of plug "B"
4 — клеммная a plate (only type 85 A) |
|
|
- Be convinced that the rotor rotates smoothly.
|
|
|
|
|
