Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
- Brake system
   + Brakes
   + Brake highway/hose the brake cylinder
   + Forward brakes
   - Lay and back brake
      + The general description
      - Diagnostics
         Check and adjustment
         Vehicle service
         Cable of a lay brake
         Brake drum
         Brake колодка
         The brake cylinder
         Back plate of a brake
   + Antiblocking brake system (ABS)
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment







e8f2b5b1

Back plate of a brake

Removal

 PERFORMANCE ORDER

  1. Execute item 1 - 5 procedures of removal Has undressed the Brake drum.
  2. Execute item 2 - 5 procedures of removal of Section Brake колодка.
  3. Execute item 3 - 4 procedures of removal Has undressed the Brake cylinder.
  1. Remove a cable (3) from a back plate of a brake (1), having compressed a cap of a cable of a lay brake (2).
  1. Merge трансмиссионное oil from a reverse gear.
  1. Remove nuts of the holder of the bearing of a wheel (1) from the case of a back shaft.
  1. Using the special tool, take out an axis of a back shaft from a back plate of a brake.
    • The special tool:
      • (A): 09943-35512
      • (B): 09942-15510
  1. Remove a back plate of a brake (3) from an axis of a back shaft (1).
1 — axes of a back shaft
2 — the wheel bearing
3 — a back plate of a brake

Installation

 PERFORMANCE ORDER

  1. Put a sealant on the interfaced surfaces of the holder of the bearing (1) and a back plate of a brake. "A": a sealant 99000-31110.

Necessarily remove old consolidation before drawing of the new.


  1. Establish a back plate of a brake (2) on an axis of a back shaft (1).
  1. Put a sealant in a connecting seam of the case of a back shaft (1) and a back plate of a brake. "A": consolidation 99000-31110.

Necessarily remove old consolidation before drawing of the new.


1 — the case of a back shaft
  1. Establish an axis of a back shaft on the case of a back shaft.
  1. Tighten nuts of a back plate of a brake according to an inhaling twisting moment. An inhaling twisting moment: a nut of a back plate of a brake (a) — 23 Н•м (2.3 kg th, 17.0 pounds-foots).
  1. Establish the wheel cylinder, and tighten bolts of the wheel cylinder and накидную a nut (or nuts) a brake highway according to an inhaling twisting moment (address to item 1 - 4 procedures of installation Has undressed the Brake cylinder).
  2. Establish a cable of a lay brake (3) on a back plate of a brake (1).
1 — a back plate of a brake
2 — a cable cap
3 — a cable of a lay brake
  1. Establish brake колодки, having addressed to item 1 - 5 procedures of installation of Section Brake колодка.
  2. Establish a brake drum. Address to Section the Brake drum.
  3. Again fill the differential case new трансмиссионным with oil of the specified mark. Address to Section Servicing in the Head Back differential.
  4. Fill a tank with a brake liquid and pit air from brake system (the operation description in Razdele Stravlivanie of air from brakes in the Head Brake system see).
  1. Establish a wheel and tighten nuts of wheels with the specified twisting moment of an inhaling. An inhaling twisting moment: a wheel nut (b): 100 Н•м (10.0 kg th, 72.5 pounds-foots).
  1. On termination of works, press the brake lever with effort about 30 kg (66 pounds) from three to ten times to receive a necessary backlash between a drum and a boot.
  2. Adjust a cable of a lay brake (for adjustment address to Section Check and adjustment of a lay brake in the Head Brake system).
  3. Establish a back central console box.
  4. Check up and be convinced that a brake drum not заедает, and brakes work correctly. Then remove a vehicle from the lift and execute check of brakes (a foot brake and a lay brake).
  5. Check up, whether there are no oil leaks in all established parts.